Fireangel CO-9X Carbon Monoxide Alarm

Product Information

In living spaces: they should be positioned close to where the occupant's head is likely to be most of the time – e.g., on your bedside table. Combined smoke & CO alarms or mains-powered CO alarms are typically installed on the ceiling and should be at least 30cm away from any wall, light fitting, or other obstruction. If you have had your FireAngel carbon monoxide alarm for a few years but it is still within warranty, and the isolation pin has been removed, please get in touch with our Customer Support team. If it is not within warranty, please replace your alarm as soon as possible. Why is my FireAngel CO alarm beeping? If your CO alarm is flashing a red LED light every 20 seconds, it has been activated recently. This is referred to as ‘alarm memory’, find out more about what this feature means here. Why does my FireAngel CO alarm not sound when I press the test button?

The FA6813-EU offers electrochemical sensing technology and a clear loud alarm to ensure trusted carbon monoxide (CO) detection for your home. This alarm also features our new Crescendo Test, which helps to protect your hearing by allowing you to choose the volume level of the test alarm. Simply hold down the test button and the alarm will move through the increasing volume levels (similar to a rising ‘crescendo’) until you find the alert sound level you are comfortable with. If your FireAngel CO alarm is fully activating, and you can hear 4 loud beeps, immediately open any doors or windows in your home, stop using any appliances, switch them off and evacuate the building taking the CO alarm with you.CE marked and Kitemarked to BS EN 50291-1 (domestic use) & BS EN 50291-2:2010 (camping/caravans/boats) Under the extended Smoke and Carbon Monoxide Alarm (England) Regulations 2015, from October 1st 2022, a carbon monoxide alarm will be required in all rooms where there is a fixed combustion appliance – such as gas boilers or gas fires – once the compliance date is announced. However, gas cookers are excluded from the updated regulation. The alarm’s high sensitivity mode will be enabled if the alarm predicts CO levels will increase to or above 180ppm for fast reaction to rising CO levels. Find out more about the FA3820X4 CO Alarm. FA3313X4: Carbon Monoxide Alarm with replaceable batteries

The FA3313X4 is the ideal replacement for end-of-life FireAngel CO-9B alarms, featuring the highest level of CO detection for your home. With intelligent CO sensing technology and built-in features including Sleep Easy function and Alarm Memory, this alarm will keep your family protected from carbon monoxide. All alarms are calibrated and rigorously tested in-house and are third party tested to receive the BSI Kitemark certification to provide peace of mind. Also, the new range is compliant with the revised European Standard EN 50291-1:2018 to ensure maximum protection. FA3322X4: Carbon Monoxide Alarm with digital display and 10 year battery Do not install CO alarms within 3 metres of doors or windows, above radiators, or immediately close to anything that gives off steam or fumes like a cooker or shower room. Similarly, it is not recommended to install detectors in dusty areas such as workshops or garages.FireAngel’s new range of carbon monoxide alarms use intelligent sensing technology for a rapid reaction to rising levels of CO. Battery powered carbon monoxide alarms can typically be installed wall-mounted or left free-standing on flat, level surface. If your CO alarm stopped beeping after being outside in the fresh air for 10 minutes, you may have a possible carbon monoxide leak in your home. We recommend calling your gas supplier or national emergency gas helpline on 0800 111 999 and await further instruction. Carbon monoxide is a highly poisonous gas, caused by fuel not burning properly. It cannot be seen, smelt or tasted by the human senses and is only detectable through a CO alarm. https://www.fireangel.co.uk/wp-content/uploads/2022/10/MA0394R1-FireAngel-CO-Icon-Guide-Blog-Assets-Identifier-Guide-Draft-1_Power-Nightime-Sensing.mp4

If your FireAngel carbon monoxide alarm is new and the test button is not working, try removing the isolation pin. Once removed, wait for at least 1 minute for alarm to initiate. If the alarm now sounds once test button is pressed your alarm is working correctly. If it still does not sound, please get in touch with our Customer Support team. An audible Carbon Monoxide detector is the only way to be alerted to a carbon monoxide leak; it can’t be smelt, tasted or seen so it’s impossible for human senses to detect.The 7 year sealed battery powered FireAngel CO-9X carbon monoxide alarm features clear LED indicators for power, fault or alarm status and a large test/reset button for ease of testing the device. The CO detector can be wall mounted for home use, or can be left free standing, making it a suitable portable detector to take on holiday. The alarm comes with 2 X AA batteries that can be replaced once the low battery chirp can be heard. However, if your CO alarm is beeping, flashing red or not responding during a test, follow our troubleshooting guide to decipher the cause. This guide applies to FireAngel FA3313 and FA3820 alarms. Why is my FireAngel CO alarm going off? With the alarm memory function, the red LED will flash to provide a visual indication of a previous CO alarm activation. Experience both audible and visual safety warnings with the digital screen, which will change colour to indicate different incident types for clear safety advice.